Drag Specialties

Made with thick 13 gauge steel for increased strength Zinc-plated for superior rust resistance Ideal for use on bikes with upgraded speaker...

Features braided lines with chrome steel fittings All measurements are approximate Made in the U.S.A.

Each meets or exceeds OEM specifications and features precise construction

Meets or exceeds OEM specifications and features precise construction

Radius license plate mounts offer a unique custom look Available for fenders up to 8" wide Three-bolt style fits most OEM fenders that have...

Includes mounting hardware

Mounting block is located at the back of the light housing, so it will fit most stock and custom applications Include a 60/55W H-4 bulb Rep...

These tip lights are a perfect fit on OEM and aftermarket front and rear fenders Clear fender light comes with amber and red bulb Replaceme...

Heim-style rod ends compensate for imperfect alignment; up to 28° off center Internally threaded with 5/16"-24 threads Great for using as s...

Hardened steel with splines; exact replacements for OEM parts

Complete rear master cylinder assemblies Polished and chrome-plated Polished and chrome-plated

Allows speedometers with a 12mm cable connection to use 5/8"-12 speedometer cable Fits all Drag Specialties mini gauges and other speedometer...

Water-resistant and vibration-resistant Accept 12mm cable Backlit with 12V bulb; replacement bulbs available separately Matching Drag Spe...

Feature chrome brake and clutch controls Die-cast aluminum switch housings have radiused edges, OEM-style clamps, smooth tops and a chrome fi...

Internal fuel line for pump to fuel filter on fuel-injected models

Includes lever and 10 mm banjo bolt

Includes all parts needed for complete rebuild of front fork leg assemblies (unless noted)

Springs are measured from hook to hook

Rebuild kits fit a variety of H-D models listed Meet or exceed OEM specifications Include metal piston

Socket-head bolt sets to meet virtually any custom need Complete motor sets for 07 and later Big Twin include bolts for primary, cam, cam sen...

OEM-style calipers in chrome finish Complete with all necessary mounting hardware and brake pads Rear calipers accept OEM bolts, shims, bus...

Specifically designed for high-performance engines that need extra cranking power Superior engineering features include a grid design for max...

Replacement kickstarter gear for Drag Specialties Kickstarter Kit

100% new - not remanufactured! Special pinion shaft threads and extended jackshaft bolt allow for a wider range of applications Starters fe...

Improves overall performance including starting, stops high-speed misfires and increases mileage 30,000 V output Peak spark voltage increases by a...

The entire line of Drag Specialties cables are made to match perfectly Lengths and nut sizes of the cables are provided for installation on c...

The entire line of Drag Specialties cables are made to match perfectly Lengths and nut sizes of the cables are provided for installation on c...

Steel construction Approximately 4-5/8" diameter Round horn covers replace the stock "cowbell" cover found on most 91-16 Big Twin and XL mo...

High-quality replacement sensors

High-quality front wheel speedometer drive units fit a variety of H-D models

One-piece construction with a chrome finish Indicates the fill level of the transmission fluid

Steel construction Always check slider covers for proper clearance. Bottom area of slider covers may need to be formed slightly to clear lo...

Works with any O2 sensor port fitting Made in the U.S.A.

Designed specifically as a direct bolt-on upgrade for Road Glide models Bars include black control clamps to replace the "oversize" OEM clamp...

Specifically designed for high-performance engines that need extra cranking power Superior engineering features include a radial grid design ...

Zinc-plated steel spacer shims for rear sprocket or belt pulley Used often when installing a wider rear tire Longer bolts may be required w...

Top-quality replacement lenses and gaskets Not DOT compliant.

For twist throttle controls measuring 7/8" to 1" Made of aluminum with black finish Sold each

Plugs have a unique look with a black ceramic body and bold red logo/script Insulator is made of 95% pure alumina, features strong resistance...

OEM-style replacement fuel filters Essential to keep bikes running in top condition

High-quality replacement rubber components

Get a smooth, clean custom look Match the rear angle of OEM saddlebags and most OEM rear fenders Provide a unique look for most models with...