Drag Specialties

Economical alternative to billet clamps

Made in the U.S.A.

Made in the U.S.A.

Features chrome steel fittings Made in the U.S.A. Meet DOT specifications All measurements are approximate.

Features chrome steel fittings Made in the U.S.A. Meet DOT specifications All measurements are approximate.

Fat Bob-style custom application, low-tunnel tank holds approximately 3.3 gallons (EU: 12,49 L) Feature a 3/8" NPT-style petcock mount with t...

Meets or exceeds OEM specification Replacement screws available separately Top plate installation screws are single-use and should be repla...

Billet aluminum construction Fit is nearly flush when closed; opens easily with just a quarter-turn of the center of cap Use OEM-style gask...

Replaces the key latch on fuel doors Includes door spring hinge pins for 92-07 and 08-15 models

Die-cast construction Mount using existing hardware

Feature a provision for evaporative emissions control equipment

Feature a provision for evaporative emissions control equipment

Features a three-position switch (on/off/reserve) Chrome plated with filter screen Has a 1/4" fuel outlet Accepts 1/4" NPT Petcock Rebuil...

Features an internal rubber mount/stud system that allows for easy installation and removal Molded flexible urethan foam interior for maximum...

3/16" ABS thermoformed seat base for a perfect fit, with a carpeted bottom and rubber bumpers to protect paint Fits with all Drag and most Ha...

Contoured seating area for maximum comfort 3/16" ABS thermoformed seat base for a perfect fit High quality automotive grade vinyl cover M...

Custom-molded polyurethane foam interior for maximum comfort 3/16" ABS thermoformed seat base for a perfect fit Fully carpeted bottom to pr...

Automotive-grade vinyl covers Molded flexible urethane foam for maximum comfort 3/16” ABS thermoformed seat base with fully carpeted bottom...

The Extended Reach seat moves the rider up and back to accommodate individuals with a longer inseam 3/16” ABS thermoformed seat base with ful...

3/16” ABS thermoformed seat base with fully carpeted bottom finishes off the seat and to protect paint Molded flexible urethane foam for maxi...

3/16" ABS thermoformed seat base for a perfect fit, with a carpeted bottom and rubber bumpers to protect paint Fits with all Drag and most Ha...

3/16" ABS thermoformed seat base for a perfect fit, with a carpeted bottom and rubber bumpers to protect paint Fits with all Drag and most Ha...

On 2010 and later models, the ECM has been relocated away from the seat area allowing a lower seat profile, improved riding height and overall ...

Feature automotive-grade vinyl in seating area and on sides Fully carpeted bottom with rubber bumpers to protect paint 3/16" ABS thermoform...

Include adjustable front seat hinge and two rear mount studs for springs Feature a heavy steel contoured seat base with a black finish Cons...

Each assembly includes a pickup, mounting plate and wires with connectors

Chrome-plated steel bracket features a retained mounting screw that stays attached with the bracket Mounting screw has a knurled edge for fin...

Cables feature polished-chrome fittings, black vinyl outer casings, tempered-steel inner conduit and an inner nylon liner for smooth operation ...

Beautifully chromed rear fender struts

Include all necessary installation hardware and instructions

Simple bolt-on installation

Features braided lines with chrome steel fittings All measurements are approximate Made in the U.S.A.

Features braided lines with chrome steel fittings Made in the U.S.A.

Include all necessary installation hardware and instructions

High-quality replacement components

Features braided lines with chrome steel fittings All measurements are approximate Made in the U.S.A.

Features braided lines with chrome steel fittings All measurements are approximate Made in the U.S.A.

All measurements are approximate Made in the U.S.A.

High quality construction Dimensions given are the bushing dimensions

Steel construction Available in chrome finish or black Feature a custom round heim joint end with 5/16" hole and/or ball joint ends with 5/...

5/16"-24 fine-thread studs allow attachment to most shift levers Studs are 12-1/4" on center Includes mounting hardware

High-quality, levers are excellent OEM replacements Strong, die-cast construction is reinforced for extra strength Shift pegs sold separate...

Billet aluminum construction Attaches to the existing OEM brake pedal Includes mounting hardware Matching shift pegs and grips available ...

Mounts measure 2-1/2"L Move the passenger pegs in closer to the bike for a more sleek look Accept most male-mount style footpegs (sold sepa...