Drag Specialties

Features braided lines with chrome steel fittings Made in the U.S.A.

Top-quality clear-coated stainless steel-braided or black vinyl-coated stainless steel/braided brake lines, banjo bolts, brake line fittings an...

Features braided lines with chrome steel fittings Made in the U.S.A.

Features braided lines with chrome steel fittings Made in the U.S.A.

Features braided lines with chrome steel fittings All measurements are approximate Made in the U.S.A.

Features braided lines with chrome steel fittings Made in the U.S.A.

All measurements are approximate Made in the U.S.A.

All measurements are approximate Made in the U.S.A.

Polished and chrome-plated OEM replacements

Used for mounting passenger footpegs or replacing existing OEM footpeg mounts Include mounting hardware Accept most male mount pegs

Rugged, die-cast aluminum construction Starter shaft bushings included; seals and other components must be ordered separately to complete ins...

High quality construction Dimensions given are the bushing dimensions

All sissy bars are constructed from 9/16" solid steel Bars are measured from the first bend to the top of the bar Sissy bars and side plate...

Cables feature polished-chrome fittings and stainless-steel braiding outer casings, tempered-steel inner conduit and an inner nylon liner for s...

Cables feature polished-chrome fittings and stainless-steel braiding outer casings, tempered-steel inner conduit and an inner nylon liner for s...

Cables feature polished-chrome fittings and stainless-steel braiding outer casings, tempered-steel inner conduit and an inner nylon liner for s...

Feature a unique textured layer of thin black rubber over a foam sleeve Chrome end caps and throttle sleeve included

Designed specifically as a direct bolt-on upgrade for Road Glide models Bars include black control clamps to replace the "oversize" OEM clamp...

The ultimate 1-1/4" diameter handlebar, designed for maximum comfort 1" diameter in clamping area Slotted and notched for Throttle-By-Wire ...

Handlebars for the "biggest fattest" look Custom bends for the ultimate in comfort Designed for use with 96 and newer style controls and master cy...

Allows mounting of 1-1/2" diameter handlebars on Springer models Includes two risers with top clamps Top clamp hardware is concealed for a ...

Fits over steering stem bolt Require 39 mm forks

Feature chrome brake and clutch controls Die-cast aluminum switch housings have radiused edges, OEM-style clamps, smooth tops and a chrome fi...

Feature chrome brake and clutch controls Die-cast aluminum switch housings have radiused edges, OEM-style clamps, smooth tops and a chrome fi...

Also features a 1/2" drive for use with a ratchet or torque wrench Necessary for removing transmission sprocket locknut

Check rear axle head and nut size before ordering to ensure proper fit Firmly attach to the axle head and nut with high quality setscrews P...

Lighted switch fits many popular switch consoles

Hydraulic brake lever

High-reliability 12V voltage regulators feature rugged aluminum alloy construction Provide accurately regulated voltage under all electrical ...

Two years of development and design went into producing a superior regulator Fully assembled in the USA with domestic made electrical boards ...

Two years of development and design went into producing a superior regulator Fully assembled in the USA with domestic made electrical boards ...

Feature encapsulated magnets in a reinforced steel shell Direct OEM replacements

Programmable with any sending unit that sends 3,000 - 90,000 pulses per mile (EU: 1,61 km) Features a 12V LED backlit display Digital odome...

OEM replacement electronic speedometer; includes all OEM gauge functions including check engine light Available in mph or km/h

Uses OEM mounting hardware; designed to use OEM style rotors, pulleys and sprockets Fully assembled and trued with bearings installed and end...

High-quality replacement battery straps are manufactured from 18-gauge stainless steel Meet or exceed OEM specifications

Simple bolt-on installation

Heavy gauge steel with reinforced seams Come complete with extra-strong mounting tabs, and mounting hardware Petcocks sold separately

High quality with a raw steel smooth finish and no taillight hole

16-gauge, deep-drawn steel Fender is 41" L x 1-1/4" D Fender bracket not included Raw steel finish

Use to install seat springs for spring-style solo seats Bolt-on design uses easy-to-install bolt-on spring mounts (drilling required); come i...

A great idea for quickly removing any seat Chrome-plated, aluminum knob with knurled edge comes with one 1/4"-28 stud and one 1/4"-20 stud fo...

Made of durable black 300 x 300 denier polyester fabric with a urethane coating and WRMR (Water-Resistant/Mildew-Resistant) finish Cover fold...

Fits Drag Specialties square sissy bars and most H-D accessory square sissy bars with a 4" i.d. (except bars with welded inserts) Feature hig...

All pads feature high-grade black vinyl coverings Each complements the bike's seat and comes complete with all necessary mounting hardware ...

Available as stock OEM replacement or custom applications with mounting bracket

Replacement rocker switches for a variety of applications

High-grade carbon steel replacement rear wheel sprocket 1.9" center hole